february 2015 for power line emc components mpz2012 2012[0805 inch]* * dimensions code jis[eia] chip beads mpz2012 ty p e mpz series (for automobiles)
(2/10) 20150203 / beads_automotive_power_mpz2012_en.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components chip beads for power line features noise reduction solution for power line. compared to the mmz series, has low direct current resi stance for compatibility with large currents, optimal for low power cons umption. various frequency characteristics with 5 materials of different features for countermeasures against everything from general si gnals to high-speed signals. performs well even in signal lines where low direct current resistanc e is required. application various ecus, powertrains, body controls, and car multimedia (telematics). part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of mpz2012 type mpz 2012 s 121 a t d25 series name lwt dimensions material name impedance characteristic type packaging style internal code (mm) ( ) at 100mhz 2012 2.01.25x0.85 s 121 120 a t taping d25 type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mpz2012 C55 to +125 C55 to +125 4,000 8 product compatible with rohs directive halogen-free compatible with lead-free solders aec-q200 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type material characteristics s material: standard type that features impedance characteristics similar to those of a typical ferrite core. for signal line applications in which the blocking region is near 100mhz. impedance values selected for effectiveness at 40 to 300mhz. typical material impedance characteristics y 0 500 1000 1500 2000 2500 10 100 1000 frequency(mhz) s
(6/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type shape & dimensions recommended land pattern 1.250.2 2.00.2 0.50.3 0.850.2 dimensions in mm dimensions in mm 1 0.8 0.8 1.2
(7/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type electrical characteristics characteristics specification table please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85c or more in temperature of the product. measurement equipment ? equivalent measurement equipment may be used. rated current vs. temperature characteristics (derating) impedance dc resistance rated current part no. [100mhz] ( ) tolerance ( )max. (a)max. 30 10 0.010 6 mpz2012s300atd25 100 25% 0.020 4 MPZ2012S101ATD25 220 25% 0.040 3 mpz2012s221atd25 330 25% 0.050 2.5 mpz2012s331atd25 600 25% 0.100 2 mpz2012s601atd25 1000 25% 0.150 1.5 mpz2012s102atd25 measurement item product no. manufacturer impedance e4991a+16192a agilent technologies dc resistance type-7556 yokogawa s300a s331a s101a s221a s601a s102a 0 1 2 3 4 5 6 7 C55 C35 C15 5 25 45 65 85 105 125 temperature ( c ) rated current ( a )
(8/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type electrical characteristics z vs. frequency characteristics (by series) mpz2012s series 100 300 500 700 1200 400 200 600 800 900 1000 1100 0 10000 1000 100 10 1 frequency ( mhz ) impedance ( ) mpz2012s102a mpz2012s221a mpz2012s101a mpz2012s300a mpz2012s331a mpz2012s601a
(9/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type electrical characteristics z, x, r vs. frequency characteristics mpz2012s300atd25 MPZ2012S101ATD25 mpz2012s221atd25 mpz2012s331atd25 mpz2012s601atd25 mpz2012s102atd25 50 40 30 20 10 0 1 10 100 1000 10000 z x r frequency ( mhz ) impedance ( ) 1 10 100 1000 10000 0 20 40 60 80 100 120 140 frequency ( mhz ) impedance ( ) z r x 300 100 50 150 200 250 0 1 10 100 1000 10000 z r x frequency ( mhz ) impedance ( ) 400 350 300 250 200 150 100 50 0 1 10 100 1000 10000 z r x frequency ( mhz ) impedance ( ) 0 100 200 300 400 500 600 700 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) z r x 1200 400 200 600 800 1000 0 1 10 100 1000 10000 z r x frequency ( mhz ) impedance ( )
(10/10) 20150203 / beads_automotive_power_mpz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mpz2012 type packaging style reel dimensions tape dimensions dimensions in mm ty p e a b p1 k mpz2012 1.50.2 2.30.2 4.00.1 1.1max. ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 dimensions in mm 1.0 ?60min. 14.4max. 8.4 +2.0 C0.0 4.00.1 2.00.05 b a p1 8.00.3 1.750.1 3.50.05 k 1.5 +0.1 0 taping 200min. 300min. drawing direction 40 to 80 dimensions in mm
|
